Shanghai Gengyun Industrial Co., Ltd
24/48-Core OPGW Optical Cable
This article examines 24/48-core OPGW optical cable as a dual-function conductor that combines overhead ground wire protection with fiber optic communication. It analyzes the layered construction that houses optical fibers within a metallic conductor, the short-circuit current capacity that determines metal cross-section, the thermal isolation that protects fibers during fault events, and the comparison with ADSS and OPPC alternatives.
Dual-Function Architecture: Ground Wire Meets Communication Channel
24/48-core OPGW integrates two otherwise separate power-grid assets into a single overhead conductor. The outer layers of aluminum-clad steel or aluminum alloy strands perform the conventional function of an overhead ground wire, while the inner optical unit provides communication capacity.
- The Ground Wire Function
The outer layers of aluminum-clad steel or aluminum alloy strands intercept lightning strikes and conduct fault current to ground. The ground wire function is the primary electrical purpose of the conductor, and the optical unit is housed within it without compromising the ground wire’s performance.
- The Optical Unit Function
Inside, a stainless steel tube or aluminum tube houses the optical fibers, protecting them from the mechanical and thermal stresses of the power-line environment. The optical unit provides the communication capacity for protection signaling, SCADA, and teleprotection.
- The Infrastructure Leverage
The utility gains a communication channel without adding a second overhead line, a second set of towers, or a second right-of-way. This dual-function architecture is the defining advantage of OPGW over any separate ground-wire-plus-fiber approach. The leverage of existing infrastructure is the economic basis of OPGW‘s dominance.
Short-Circuit Capacity and Tensile Strength
Unlike telecommunications cables, OPGW must satisfy electrical specifications that have no counterpart in datacom fiber. The short-circuit current capacity and the rated tensile strength determine the cable’s metal cross-section and therefore its diameter and weight.
- Short-Circuit Current Capacity
The short-circuit current capacity—expressed in kA²s—determines how much fault current the cable can carry before the optical unit overheats. A typical 95 mm² OPGW handles 25 kA for 0.3 seconds. The capacity depends on the metal cross-section and the thermal mass of the conductor.
- Rated Tensile Strength
The rated tensile strength (RTS) must support the span under wind and ice loads; 12-core designs typically exceed 100 kN. The RTS depends on the strength of the metallic strands and the cable’s overall construction. The RTS and the short-circuit capacity together define the cable’s mechanical and electrical performance.
- The Fiber Count as a Secondary Specification
These two parameters, not fiber count, often dictate the cable’s metal cross-section and therefore its diameter and weight. OPGW procurement begins with fault-current and span calculations, and fiber count follows from communication requirements. The 24 or 48 fibers fit within the same tube envelope in most designs, so fiber count is a secondary specification.
Thermal Isolation of the Optical Unit
The optical fibers inside OPGW sit millimeters from conductors that may reach 200°C or more during a fault. The design must keep the fiber below its long-term temperature limit while the metal layers absorb and dissipate fault energy.
- Excess Fiber Length and Loose-Tube Structur
Manufacturers achieve thermal isolation through a loose-tube or central-tube structure with excess fiber length. The excess length allows the fiber to contract and expand without stress during thermal cycling. The loose tube also provides space for the fiber to move, reducing microbending loss.
- Water-Blocking Gel with Hydrogen Absorption
Water-blocking gel with hydrogen-absorbing capability protects the fiber from moisture and hydrogen. Hydrogen generated by polymer decomposition can enter the silica and increase attenuation at 1383 nm. The hydrogen-absorbing gel captures the hydrogen before it reaches the fiber.
- Thermal Barriers Between Tube and Strands
Thermal barriers between the tube and the outer strands slow the heat transfer during a fault. The barriers provide time for the metal layers to absorb and dissipate the fault energy before the fiber reaches its temperature limit. The thermal design is the single most important differentiator among OPGW suppliers.
Comparison with ADSS and OPPC
OPGW competes with ADSS and OPPC in the power-utility communication space, and the choice depends on line voltage and structure.
- OPGW vs. ADSS: Voltage-Level Segmentation
ADSS installs on lower-voltage lines or separate poles at lower cost but cannot match OPGW’s fault-current capacity and mechanical robustness on high-voltage towers. OPGW remains the default on 220 kV and above because it uses the ground-wire position that already exists.
- OPGW vs. OPPC: Ground Wire vs. Phase Conductor
OPPC replaces a phase conductor and carries continuous load current, making it suitable for situations where ground-wire space is unavailable. OPGW replaces the ground wire and carries only fault current during emergencies. The choice depends on whether ground-wire space is available and whether continuous current carrying is required.
- The Secure Position in the Core Segment
OPGW’s competitive position is secure in its core segment. The substitution threat comes mainly from ADSS at lower voltages, not from OPPC at higher voltages. The ground-wire position that already exists on every high-voltage tower is the basis of OPGW’s dominance.
FAQs
1. Why does OPGW fiber count (24 vs. 48) matter less than short-circuit rating in cable selection?
The short-circuit rating determines the metal cross-section needed to survive fault current without damaging the optical unit. That cross-section often sets the cable diameter and weight regardless of fiber count. Once the electrical design is fixed, 24 or 48 fibers fit within the same tube envelope in most designs.
2. What happens to the fibers during a fault if thermal isolation is inadequate?
The fibers experience rapid temperature rise, causing the coating to degrade and the glass to weaken. Excess fiber length may migrate, creating microbending loss. Hydrogen generated by polymer decomposition can enter the silica and increase attenuation at 1383 nm. These effects may not appear immediately but emerge months after the fault.
3. How does OPGW differ from OPPC (optical phase conductor)?
OPGW replaces the ground wire and carries only fault current during emergencies. OPPC replaces a phase conductor and carries continuous load current, so its thermal design must handle steady-state heating as well as fault transients. OPPC is used where ground-wire space is unavailable or where phase-conductor communication is preferred.
4. Why is OPGW the default on 220 kV and above?
Every high-voltage line already requires a ground wire, and OPGW uses that existing position without requiring a separate communication route. The ground-wire position provides the mechanical and electrical performance the grid requires, and the optical unit adds communication capacity at marginal incremental cost.
Company Introduction: With over 20 years of deep industry expertise, we specialize in customizing and supplying solutions for optical fibers, cables, raw materials, and manufacturing equipment. We deliver reliable technical support and product services.
About the Author: With 20 years of hands-on experience in optical transmission media, cable assemblies, and core substrate materials, we offer practical, expert insights grounded in full-industry-chain expertise.
